Post Production of 3D Prints #1

[My Miniature Madness]

Post Production of 3D Prints #1

 

If you've stopped by to see what I am up to recently, you know that I wanted to try something completely new with the Alki Point project; making 3D printed items for the majority of the interior design. I have most of them in my hands, but now what do I do?

 

I needed to decide what I wanted the finishes to look like, and then do a little execution research. What type of adhesive should I use to adhere them to my wooden dollhouse walls? How about gluing it to one another? What kind of paint should I use? Can they be sanded? Primed? Filled? Do they melt like foam does if spray painted?

 

Several hours of research later, I came away from the Shapeways Forum on Post Production Techniques like most everything else I research. There is really no absolute. Try what works for you and then post your experience to the collective record in the forum. Okay, so I am going to experiment a little, and hope I don't ruin anything in the process.

 

I should point out that there are many, many different types of material available for you to have items printed in. Plastics, metals, precious metals, sandstone, ceramic, acrylic etc. I have only had them printed in three different materials so far:

 

~White, Strong & Flexible - Flexible, slightly gritty surface, bright white.

~White, Strong & Flexible Polished - Smoother finish, slightly glossy, bright white.

~Metallic Plastic - Grey with metallic specks, stiff and brittle.

 

So, until I am able to purchase things in other print materials, this post will pertain only to White, Strong & Flexible and White, Strong & Flexible Polished.

 

The forums pretty universally recommended that you wash all WS&F pieces thoroughly with soap and water. I filled up a Rubbermaid tray with hot, dish soapy water and used a washcloth to scrub each piece. After a good rinsing, I laid them on paper towels to dry.

 

 

 

 

 

The WS&F material is actually Nylon 12. It is pretty porous when not polished, so sealing it with a dip of Future wax or priming before painting was also recommended. I wanted to see how porous it would be un-primed as part of the experimenting.

 

I didn't have to buy any paint or sealer because I already had these on hand. The Krylon is supposed to be white paint and primer in one. The chrome metallic does not say to use on plastic. It says "for use on wood, metal and more". I hoped the "more" meant Nylon 12. I probably really need to varnish the metallic finish afterwords, so I'll give the gloss spray Mod Podge a try.  

 

 

 

 

 

 

The white paint took four light coats to reach this point. I just coated each piece lightly, letting each coat dry for about 45 minutes in between. One of the tile walls was printed in WS&F Polished. I noticed a more uniform coat of paint, and it seemed to soak into the nylon less. My conclusion is to pay the extra few cents when possible, and have the piece polished. Feels and looks smoother, as well.

 

 

The metallic paint is certainly more apt to soak in. I painted at least five coats, also letting them dry thoroughly in between. When I would go out to the garage to check on them, you could see the nylon white coming through in some spots. Notice the piece of wood I am using - the chrome looks promising!

 

 

 

 

 

The high temperature today was 39 degrees, so it is cold, but the humidity is low. I had a space heater in the insulated garage, so it was probably somewhere in the 60's in the airspace around the paint. I am going to let all of the pieces dry overnight, then I'll varnish the chrome pieces.

 

My next post on Post Production of 3D Prints will be about what I find attempting to glue the shower tile walls to the wood bathroom walls.

 

Until then, I am going put on some bigfoot podcasts, measure the bathroom and kitchen and start making the cabinets!

 

If you are planning to buy and finish any 3D printed miniatures in the future, here are a couple of helpful tutorials from Shapeways on glues and paint:

 

Gluing 3D Printed Parts

Painting 3D Printed Models

 

The code for 20% Off + Free Shipping this weekend is BFDEALS.

My designs can be found here: https://www.shapeways.com/shops/myminiaturemadness?sort=newest

[Sable]

Wow!!!!!! 

[Sable]

A high gloss white spray paint will make the bath fixtures look like porcelain.

[My Miniature Madness]

40 minutes ago, Sable said:

A high gloss white spray paint will make the bath fixtures look like porcelain.

I think you are right, Sable! The paint I used on them is a satin finish, and I am liking the way they are looking! I am gluing in the shower pan, now. Getting very excited to finally see it coming together!